Shark Vacuum Brush Not Spinning

Q: Why Is My Shark Not Picking Up?

The shark vacuum may not pick up because the filters might not be cleaned. Dirt and debris can clog air filters and thus makes their suction power low.

Shark vacuums can clean effectively, and they are long-lasting. Sometimes, there are problems like the shark vacuum brush not spinning even it is powered on.

The design of the shark vacuums is easy to break down. Therefore, you can discover the fault quickly.

In case your shark vacuum stops working, its settings could be wrong, the belt might be broken, or the nozzle might be disconnected.

While spinning, if it stops suddenly, maybe some parts do not work due to shark vacuum overheating. This guide will help you know the causes of why the shark vacuum brush is not spinning?

What you can do at your home without hiring a professional to fix this problem?

Shark Vacuum Brush Not Spinning: Reasons & Fixes

Some of the major reasons why the brush of your shark vacuum is not spinning along with their solutions are:

Shark Rotator Brush Roll Not Working

A roller brush with the shark vacuum called carpet mode spins the brush. Better switch to power and brush roll mode to spin the roller brush. Or else the roller won’t spin as it is set to just power or floor model.

If the shark vacuum brush roll indicator light is not on, it will not work properly. It should be green. When you tilt the vacuum back, then it will activate. Standing upright will not activate it.

Floor Nozzle is Disengaged

Attach the nozzle properly to make the roller brushwork.

Check the nozzle’s tight connection by pressing down on the handle with a strong grip. If you can’t properly arrange the nozzle, continue to unplug the vacuum and break the connection of the nozzle.

Clean the nozzle from dirt and debris, and then connect the vacuum again.

Debris or Hair on the Brush

Hairbrushes often get dirty too quickly and catch debris because they are wrapped with hair. This ceases the spinning of the shark brush roll. Not cleaning the brush on time causes such things to happen.

Cut the hair wrapped around the brush with scissors. If the hair buildup is too heavy, it would be better to use a razor blade. Be mindful not to cut the bristles or any part of the brush.

Broken Shark Vacuum Belt

The older versions of shark vacuum cleaners used the belt to make the roller brush spin. In the current versions, they use the “tripped” reset systems.

The brush will not work if the belt is damaged or broken. Now, shark vacuum belt replacement is required.

Shark Vacuum is Not Sucking – Quick Fix

If the vacuum brush ceases to spin and the suction power is not working, ensure there is resistance in the dust cap or hose. Usually, the resistances in the dust cap can easily be noticed as it is emptied.

That is why clean and empty the dust cap to observe the blockages. Press the quick-release pedal and separate the hose to check hose for debris.

Make sure you can notice if there is any blockage in the hose. Keep in mind that the things that block the hose may not be sufficient to cease the suction, but it will certainly affect how the vacuum sounds when working.

Shark Vacuum Troubleshooting Tips

Here are some quick yet effective tips to troubleshoot your shark vacuum in no time.

How to Clean Shark Vacuum Brush Roll

The shark vacuum brush roll requires regular cleaning for the most favorable action. Too much dirt, grime, or hair buildup on the roll may result in the brush stopping to spin.

Following are some actions to be taken to clean the brush roll

Disconnect the vacuum. Check the three plastic knobs in the brush roll plate and undo their lock.
Detach the belt. It is up to you to take out the brush bar or not; however, for a detailed clean, better separate the bar.
Cut the hair or strings that might be wrapped in the brush using scissors. There is a hair removal tool that shark does have. These may come with The vacuum.
Thoroughly clean the bar since all the hair and string can obstruct the vacuum’s suction power.

How to Replace the Roller Belt

Out of the most common causes that the shark vacuum brush ceases to spin is a damaged or ruined roller belt.

Things Required

Metal spudger
Screwdriver

Steps to Follow:

When pressing the lift away button, pull the handle to detach the vacuum body.
Two small wheels are present on the bottom of the vacuum. Remove them by using a metal spudger.
Remove the nine 16 mm screws from the bottom of the panel by using the screwdriver. Side tabs must be pushed in the middle of the panel firmly. There are more 13.5 mm screws in the hose connection. Use a screwdriver to take them out.
Take out the top cover. A wire connected through a pin will be visible. Remove it by pulling up and squeezing.
Use the screwdriver to remove the 11mm screws. Now open the cover and take the roller brush out.
Take out the belt near the roller brush and replace it with a new belt. Replace the new belt near the roller brush. Follow the directions to reconstruct the vacuum.

These directions will be best for traditional drive belt shark vacuums. If there are other belts in the shark vacuums, use the user guide to replace them.

How to Keep Shark Vacuum Work Good

Clean the filters of the vacuum once a month. If you are using it after construction, clean it more often.
Clean all the dust and debris from the rotating roller bar. In this way, the brush will be clear.
To get rid of clogging, you should empty the dust bag after using it every time.
While vacuuming, do not clean bits of thread, pieces of paper, bobby pins, and wrappers of packed items. You should pick up the large mess manually. Picking it up by using a vacuum can ruin it.

How to Maintain Your Shark Vacuum

It would be best to take care of your vacuum cleaner by keeping it clean and maintained. Make sure every part of the vacuum is in good condition.

Every part of the vacuum must be running, most importantly the brush roll.

How to Clean the Filters

If you use vacuums a lot, you should clean their filter every four weeks. You can clean it every couple of months, depending on its use.

Pre-motor filters should be removed from the shark vacuum cleaner. Pre-motor filters are a combination of the felt filter and foam filter.
Turn on the filters in warm water so that the water is clear. Now gently wash the filters manually.
Take out the post-motor filter. Standard HEPA filters are available in most shark vacuums. You must check in the user guide whether your model has HEPA filters.
Under the cold water, turn on the HEPA filters.
Completely dry out all filters. The experts on sharks recommend that the filters leave out for 24 hours to completely dry.
Now, place the filters into the vacuum.

Contact Shark Customer Service

If you are still facing a problem while using a shark vacuum cleaner and the brush does not rotate by trying all the tips, contact the customer services of shark vacuums.

FAQs – Frequently Asked Questions

Why Won’t My Shark Rotator Brush Spin?

Brush on your shark vacuum will not spin if the brush bar has a blockage. To prevent any damage, the vacuum will automatically stop.

What Do You Do When a Shark Vacuum Brush Stops Spinning?

Make sure you have turned on carpet mode
Ensure the brush of your vacuum has no blockage
Filters should be cleaned
Reconstruct the vacuum’s parts and plug it
Examine the working of your vacuum
Ask customer services

Is There a Reset Button on A Shark Vacuum?

The reset button of a shark vacuum is located at the bottom of the vacuum.

Why Is My Shark Not Picking Up?

The shark vacuum may not pick up due to uncleaned filters. Dirt and debris can clog air filters and thus makes their suction power low.

How Do I Reset My Shark Vacuum?

Keep the power button in the on-off position and unplug the vacuum. After cooling it completely, plug it again.

Conclusion

Shark vacuums provide superior and outstanding performance. It will work with only a little maintenance.

Sometimes the brush does not spin, but you can fix the problem. Clean shark vacuum or removing the weary parts and installing new ones to tackle this issue. The procedure of its fixing is easy and quick to do.

There is no need to spend money on buying a new shark vacuum when you can fix it. You can enjoy your current vacuum cleaner for a long time, and its performance will be the same.

I hope this guide will be helpful to you.